Wednesday, July 18, 2012

New pictures and an updated calender...

..is now available at the website. The pictures are mostly from our recent visit in Oberpfaffenhofen where our CDR were held.

I've also updated the calender which has been out of date for a long long time. At the moment the major milestones are presented, but it will be updated continuously when Team SOLAR is up to something exciting.

ciao!

CDR

Hi.

sorry for the low activity on the blog, I guess it's the summer syndrome ;)

Well, two weeks ago we had our Critical Design Review (CDR) in Oberpfaffenhofen, Germany, where Anders, Björn P, Maja and Emil represented our team and presented our current design and status in the project. It went well and there were mostly details to fix. So that's what we will do until 2nd of August when we have the deadline for our next SED version.

We have also ordered the main parts to our chambers, so it will be really exciting to see the result after the summer.

Monday, June 18, 2012

Soldering Procedure


As you probably already know we will perform the soldring using resistance wires which will be powered and heated by copper plates which will be provided with power from the batteries. In this post I will explain the soldering procedure in more detail.

We will use a component pin to be soldered. The resistance wire will be twisted with quite a few revolutions around the component pin as seen in the figure below.



Then, the solder will be twisted around the component pin and hence around the resistance wire. The solder will be twisted very compact with alot of revolutions. This can be seen in the figure below.



When both wires have been twisted around the component pin it's ready to be powered. As the resistance wire will increase in temperature it will heat the component pin and melt the solder so it can stick to the component pin. The result can be seen in the figure below.



To ensure all samples have the same starting conditions all resistance wires will be of the same length, just as the component pins and soldering wires respectively. All resistance wires will also be twisted the same amount of revolutions around the component pin, just like the soldering wires.

Tuesday, June 12, 2012

Hello Everybody!

As promised, I will present some pictures of our experiment with the current and hopefully final desig :). The big differenses from teh previous design is the size and layout of the electronics box, the size of the battery pack, the position of  the resistance wires, the size of the hole for the cable feed through and the layout. In this post some parts will also be explained in more detail. Some may have been mentioned before, but it is always good with some repetition ;).

Here is the layout of the experiment. In front you can the vacuum and the pressurized chamber respectively and behind the electronics box and battery pack. The hole in the front is for all d-sub cables that will go through the rocket.




Here is the experiment mounted in the 120 mm rocket module. On the outside of the  module you can see a protection cap  for the venting hole which will provide vacuum in the module. A corresponding hole is also visible on the opposite side.





Each Chamber will consist of this base where two PCBs will be attched. The PCB to the right is for our pressure and temperature sensors. The one to the left is the experiment PCB. Three resistance wires will be attched to the brown copper plates with screws. The wires will be powered with cables from the batteries, which will be attached to the copper plates using the screws beside. To prevent a short circuit there will be a slit below each copper plate. As power is led to the copper plates the resistance wires will increase in temperatue en melt the solder samples twisted around the wires. (I will explain the implementation of the solder samples in more detail in a future blog post). The hole in front of the PCBs is the inlet for the d-sub 9 contact that will provide the chamber with power.


Each chamber will be covered with this hat. The hat for the pressurized chamber will have a track at the bottom as can be seen in the picture. An o-ring will be placed in the track to keep the chamber airtight. The other hat will not have this track, but it vill have a hole at the top so vakuum can be achieved.

The Electronics box will consist of two layers of PCBs to ensure that all components will fit. 
There will be a stabilization rod for the upper layer to prevent vibrations. There will also be four inlets to the electronics box; one for the d-sub15 contact from the REXUS service module, two for the d-sub 9 contacts that will provide the chambers with power and one from the batteries.




This was all for today folks!

Thank you for reading, over and out!


Thursday, June 7, 2012

Hello!

The past week we have worked very intense with the project and submitted everything in the SED which will be handed in on Monday. The mechanical design is now as well as all major and the most minor electrical components. Also the programming part has developed quite alot past week. We have also completed the majority of the simulations, it's just the thermal simulation software that still doesn't want to cooperate, but it will be fixed before monday.

As soon as the SED is handed in on Monday and there is no turning back regarding design before the CDR, I will upload pictures of the project, both here, on the website and on our facebook fanpage, so stay tuned.

Wednesday, May 30, 2012

Hey!

Today we finished our last exam for this semester, which means that we can fully focus on project until the CDR in the beginning of July. The blog will also be updated more frequently, which it hasn't been the last weeks.

The upcoming days we will make our last simulations, adjust a few on the design, work on the electrical schematics on a more detailed level, start coding and update the SED.

Sunday, April 29, 2012

Good Evening!

Tomorrow we have our deadline for the SED v1-2. So I think it is time to show you our current design and layout. As you might have noticed it changes quite often ;).

In comparison with the previous layout you can see that the battry pack stands for it self and the size of the electronics box has been reduced. For this layout we also use another bulkhead to ease the mounting and reduce the mass.
The layout seen from above.

The electronics box is as mentioned, reduced by size. Inside the box we will have two PCB's for the electronics. These  will be separated using twelwe spacers. The spacers will also be used for the attachment of the PCB's.

The outer structure of the chambers have not been changed since the last pictures, but the  inner structure is more detailed. We have added a small PCB where the temperature and pressure sensor will be placed. 




Power will be conducted to the brown copper plate using cables attached to the four screws at the corners. The  power will be led to the resistance wires which will be attached to the copper plates. The resistance wire will then heat and melt the solder wire wrapped around the resistance wire. 
To prevent a short circuit, a slit will be made below each copper plate .